高強度英文？這幾個詞的英文分別是：高強度：high strength 高精度：high precision 高技術性 ： high technology 注：尊重知識，請提問者盡快采納答案。那么，高強度英文？一起來了解一下吧。
高強度鋼
high-duty steel
high-strength steel
high-tensile steel
HSS:高強鋼(high strength steel),AHSS先進高強度鋼:(advanced high strength steel) ,是基于高強度鋼(HSS)提出來的.
AHSS
先進高強度鋼,國際鋼鐵協會( IISI) 先進高強鋼應用指南第三版中將高強鋼分為傳統高強鋼(Conventional HSS) 和先進高強鋼(AHSS) 。傳統高強鋼、烘烤硬化(BH) 鋼、高強度無間隙原子(HSS -IF) 鋼和高強度低合金(HSLA) 鋼;AHSS 主要包括雙相(DP) 鋼、相變誘導塑性(TRIP) 鋼、馬氏體(M) 鋼、復相(CP) 鋼、熱成形(HF) 鋼、孿晶誘導塑性(TWIP) 鋼和淬火分離(QP)鋼;AHSS的強度在500MPa到1500MPa之間,具有很好吸能性,在汽車輕量化和提高安全性方面起著非常重要的作用,已經廣泛應用于汽車工業,和加強件如A/B/C柱、車門檻、前后保險杠、車門防撞梁、橫梁、縱梁、座椅滑軌等零件; DP鋼最早于1983年由瑞典SSAB鋼板有限公司實現量產。
先進高強度鋼,也稱為高級高強度鋼,其英文縮寫為AHSS(Advanced High Strength Steel)。
intensive
可以表示物理上的訓練,比如體育訓練
也可以表示抽象的
比如intensive English class,英語強化班
柴油機Diesel Engine
機艙Engine room Engine room casing
主機Main engine
付機Auxiliary engine
機座 機架 貫穿螺栓轉車機
Bedplate Engine frameTie rodTurning gear
自由端 飛輪端機件 運動部件 部件、零件
Free end Fly wheel end Machinery componentsMoving parts Parts
附件緊固件
Fittings, mountings
Fixture
氣缸： Cylinder
A 列缸組第X 組：A bank No.3 cylinder unit
氣缸體Cylinder block
氣缸蓋Cylinder cover
缸套冷卻腔Cylinder jacket
缸套（襯） Cylinder liner
氣缸壁Cylinder wall
活塞： Piston
活塞頂Piston crown
活塞頭Piston head
活塞桿Piston rod
活塞桿填料函Piston rod stuffing box
活塞環Piston ring
活塞環槽Piston ring groove
活塞銷Piston pin, gudgeon pin
活塞銷軸承Piston pin bush
活塞裙邊Piston skirt
耐磨環Wear ring
33
活塞閥Piston valve
活塞泵
二沖程; 四沖程
上死點; 下死點
Piston pump
Two-stroke; four-stroke
Top dead centre; bottom dead centre
曲軸： Cranksha ft
曲軸軸承
曲軸聯軸器法蘭
Cranksha ft bearing
Cranksha ft coupling fla nge
曲柄箱
曲柄箱防爆門
Crankcase
Crankcase explosion relief valve
曲柄、曲拐Crank
曲柄銷
曲柄臂
曲軸箱門
觀察孔
Crankpin
Crankweb
Crankcase door
Sight hole
曲軸箱安全閥
曲軸箱泄油管
油霧探測器
Relief valve of crankcase
Oil drain pipe of crankcase
Oil mist detector
曲柄彎程Crank throw
連桿Connecting rod
連桿大端軸承Bearing at bottom end of connecting rod;
Bottom end bearing
連桿小端軸承Bearing at top end of connecting rod;
十字頭
十字頭銷
十字頭軸承
主軸承
主軸頸
Top end bearing
Crosshead
Crosshead pin
Crosshead bearing
Main bearing
Main journal
凸輪軸Camsha ft
驅動凸輪軸的鋼質大齒輪
示功閥
Steel gear wheel for camsha ft drive
Indicator valve
氣缸安全閥Safety valve
進氣閥Inlet valve
排氣閥Exhaust valve
搖臂Rocker arm
導板Guide
滑板Slide guide
滑塊Slid ing block
頂桿Push rod
燃油供給系統:
Fuel
(oil)
supply
system:
燃油增壓泵Fuel oil boost pump
主供給泵Main supply pump
備用泵Standby pump
34
燃油過濾器Fuel oil filter
重油沉淀柜Heavy fuel oil settling tank
重油日用柜Heavy fuel oil service tank
柴油柜Diesel oil tank
分離機Centrifuge
加熱器Heater
粘度調節器Viscosity regulator
壓力調節閥Pressure regulating valve
三通閥Three-way valve
平衡閥Balance valve
輸送泵Transfer pump
燃油噴射系統:
Fuel
(oil)
injection
system:
高壓油泵（油頭閥） Fuel oil injection pump, injection fuel valve,
High pressure oil pump
噴射泵Injection pump
燃油噴射器（油頭） Fuel injector
噴嘴Nozzle
止回閥Non-return valve
針閥Needle valve
正時調節閥Timing valve
溢流閥Spill valve
節流閥Throttle valve
柱塞Plunger
小(副)齒輪裝置Pinion arrangement
中間軸Intermed iate spind le
彈簧Spring
壓緊螺母Compression nut
凸輪Cam
凸輪軸
齒條：
齒條復板
齒條擋板
Camsha ft
Rack
Rack chord
Shield of rack
增壓器：
渦輪增壓器
廢氣渦輪增壓器
增壓器蝸殼
Supercharger
Turbocharger
Exhaust gas turbocharger
spiral casing of the supercharger
透平葉輪Turbine impeller
(透平增壓器)廢氣出口接頭Exhaust connection
渦輪端Turbine end
空壓機端Air compressor end
應急鼓風機Emergency blower
蒸汽輪機Steam turbine
鼓風機： Blower
35
渦輪鼓風機Turbo-blower
掃氣： Scavenging
橫流掃氣cross-flow scavenging
回流掃氣loop scavenging
直流掃氣uniflow scavenging
掃氣口Scavenge port
掃氣道Scavenge trunk
掃氣防爆裝置Scavenge relief device
進氣口Inlet port
排氣口Exhaust port
潤滑系統:
Lubricating
(oil)
system:
儲油槽Oil sump
泄油柜Drain tank
濾器Filter, strainer
冷卻器Cooler
液位指示器Level gauge
貯存柜Storage tank
冷卻系統:
Cooling
system:
主機淡水冷卻泵M.E. fresh water cooling pump
備用淡水冷卻泵Reverse fresh water cooling pump
主機海水冷卻泵M.E. sea water cooling pump
備用海水冷卻泵Reverse sea water cooling pump
缸套冷卻水泵Jacket cooling pump
活塞冷卻水(油)系統Piston cooling system (oil/water)
油頭冷卻泵Fuel valve cooling pump
付機淡水冷卻泵Aux. E. fresh water cooling pump
付機海水冷卻泵Aux. E. sea water cooling pump
熱交換器:
Heat
exchanger:
主機淡水冷卻器M.E. fresh water cooler
活塞水冷卻器Piston water cooler
主機油頭冷卻器M.E. fuel valve cooler
缸套水冷卻器jacket water cooler
付機淡水冷卻器Aux. E. fresh water cooler
海水循環冷卻器Sea water circulated cooler
壓縮空氣系統:
Compressed
air
system:
空氣壓縮機Air compressor
空氣瓶Air receiver
易熔塞Fusible plug
高壓空氣管High-pressure air pipe
36
空氣起動閥Air starting valve
隔離止回閥Isola ting non-return valve
釋放閥Relief valve
空氣分配器Air distributor
阻火器Flame trap
爆炸（保險）膜片Bursting disc(k)
操縱裝置Control device
安全裝置Safety device
調速器： Governor
機械調速器Mecha nical governor
電動調速器Electric governor
速度傳感裝置Speed sensing arrangement
液壓機構Hydraulic unit
慣性配重裝置Flyweight assembly
齒輪Gear wheel
速度選擇器Speed selector
油霧探測器Oil mist detector
聯軸節： Coupling:
彈性Elastic coupling
撓性Flexible coupling
機械Mecha nical coupling
電動Electrica l coupling
液力Hydraulic coupling
液壓Fluid coupling
氣動Pneumatic coupling
電磁Electroma gnetic coupling
離合器： Clutch
操縱手柄
手柄定位插銷
支架
驅動機構
Control handle
Set pin
Support
Driving unit
傳動機構Driven unit
驅動葉輪Driving impeller
傳動葉輪Driven runner
傳動裝置Gearing arrangement
大齒輪Gearwheel
小齒輪Pinion
齒輪箱Gearbox
倒車齒輪Reversing gear
倒車齒輪箱Reversing gearbox
轉動葉片Rotating vane
軸、軸承及螺旋漿Shaft,
Bearing
and
Propeller
37
軸系
軸
Shafting
Shaft
（指機械傳動軸）
推力軸Thrust shaft
推力環Thrust collar
推力塊Thrust block
中間軸Intermed iate shaft
螺旋漿軸Propeller/screw shaft
尾軸Tail shaft
尾管軸Tube shaft
實心軸Solid shaft
空心軸Hollow shaft
曲軸Crank shaft
曲軸臂Crank web
甩檔，曲軸臂撓曲Crankshaft deflection
凸輪軸Camsha ft
蝸桿軸Worm shaft
鏈輪軸Sprocket shaft
鏈輪箱Sprocket casing
軸套Shaft liner
軸襯Shaft (axis) bush
固定法蘭Fixed fla nge
聯軸節Shaft coupling
彈性聯軸節Flexible coupling
液壓聯軸節(液壓法蘭) Fluid coupling
液力偶合器Hydraulic coupling
磨擦離合器Friction clutch
電磁離合器Electric coupling
法蘭螺栓Flange bolt
鍵槽： Keyway:
湯匙形round-ended
雪撬形sled runner
普通鍵槽keyed
無鍵keyless
尾軸管Stern tube:
鑄鋼與鋼板焊接式cast steel and steel plate welded
鍛鋼與鋼板焊接式forged steel and steel plate welded
尾軸承stern bearing:
鐵梨木lignum vitae
合成橡膠synthetic rubber
塑料plastic
白合金（巴氏合金）white-meta l
油封裝置Oil gla nd
38
軸（相當于定位肖）
下沉量
Axis; spind le
Wear-down
對中Alignment
頂舉系數Jack factor
偏移Sag
曲折Gap
扭轉振動Torsional vibration
單節；雙節Single node; Two node
共振Resonance
轉速禁區范圍Restricted speed range
扭轉振動許用應力Allowable vibration stress
瞬時許用應力Allowable transient vibration stress
軸承Bearing
主軸承Main bearing
中間軸軸承Intermed iate bearing
推力軸承Thrust bearing
曲軸軸承Crank (sha ft) bearing
滾柱軸承Roller bearing
滾珠軸承Ball bearing
鐵梨木軸承Lignum vitae bearing
尾軸管軸承Stern tube bearing
軸瓦bush
軸承支架bearing support
軸承承窩bearing socket
軸承墊片bearing shim
軸承殼bearing shell
軸承座bearing seat (pedestal)
軸承蓋bearing cap (cover)
軸承塊bearing block
軸承環bearing collar (ring)
保持圈Retaining ring
螺旋漿Propeller
整體式螺旋漿Solid propeller
組合式螺旋漿Built-up propeller
可調節螺距螺旋漿Controllable pitch propeller
全方位式螺旋漿Directiona l propeller
39
材料materia l:
錳鐵黃銅Manganese iron brass
高鋁高強度黃銅High aluminium high strength brass
高錳鋁青銅High ma nganese aluminium bronze
鑄鐵Cast iron
鑄鋼Cast steel
塑料Plastic
HSS:高強鋼(high strength steel)
AHSS先進高強度鋼:(advanced high strength steel) ,是基于高強度鋼（HSS）提出來的.
以上就是高強度英文的全部內容，先進高強度鋼,也稱為高級高強度鋼,其英文縮寫為AHSS(Advanced High Strength Steel)。國際鋼鐵協會( IISI) 先進高強鋼應用指南第三版中將高強鋼分為傳統高強鋼(Conventional HSS) 和先進高強鋼(AHSS) 。 傳統高強鋼主要包括碳錳鋼(C -Mn)、烘烤硬化(BH) 鋼、。
